CAN to Ethernet / Modbus TCP / Modbus RTU Converter. Supports operating temperatures between -25 to 75°C.

I-7540D-MTCP

CAN to Ethernet / Modbus TCP / Modbus RTU Converter. Supports operating temperatures between -25 to 75°C.

  Price:  $659.00  

Features

I-7540D-MTCP is a CAN to Ethernet / Modbus TCP / Modbus RTU Converter. It is helpful for exchanging data between Modbus devices and CAN devices. I-7540D-MTCP is a Modbus TCP server and acts as slave device in Modbus RTU networks. It supports four communication modes: Modbus TCP, Modbus RTU, CAN-Ethernet Conversion and Pair connection.

The major function of the I-7540D-MTCP is a CAN to Modbus TCP/RTU gateway. It allows Modbus TCP/RTU devices to communicate with CAN devices on a CAN network. I-7540D-MTCP supports the function codes 0x03/0x04/0x10 of Modbus TCP/RTU for reading and writing of CAN messages. The device supports a transparent, protocol-independent transfer of the CAN messages, thus allowing its implementation into a wide range of possible applications. The CAN-Modbus Converter can be used with various higher layer CAN protocols (e.g. CANopen, DeviceNet or other proprietary protocols). These application diagrams show the application architecture for the I-7540D CAN-Modbus Converter.
Modbus TCP / RTU to CAN
Modbus TCP / RTU to CAN

  • Features:
    • 80186-80 Embedded CPU, or compatible
    • Ethernet Protocols, TCP,UDP,IP,ICMP,ARP
    • COM driver support interrupt & 1K QUEUE Input & Output buffer
    • Provide 200 CAN frames buffer in CAN to Modbus Mode
    • NXP 82C 250 CAN Transceiver
    • Support both CAN specification 2.0A and 2.0B
    • Max transmission speed up to 1M bps for CAN and 115.2kbps for RS-232 & RS-485
    • Max transmission distance of CAN over 1000m (follow CAN specification)
    • 7-segment LED display to Module IP, RS-232 baud rate, CAN configuration…
    • CAN Error/Tx/Rx LED indicator
    • Software configurable CAN and RS-232 communication parameters
    • Firmware updated from COM1 or Ethernet port
    • Support Web Configuration
    • Support maximum 24 Ethernet clients connection
    • Support function code 0x03/0x04/0x10 of Modbus TCP/RTU command for reading and writing CAN message
    • Provide the transparent communication between the CAN devices via Ethernet
    • Support 30 specific CAN IDs in the Modbus TCP/RTU mode

  • Applications:
    • Factory Automation
    • Building Automation
    • Home Automation
    • Control Systems
    • Monitoring Systems
    • Vehicle Automation


  • CAN bus Power Meter Solution
    • The PM-213x-CAN series power meter provides the CAN bus interface for users to easily gather the real-time power consumption information in their CAN applications. The PM-213x-CAN provides the Auto-Response mode which responses messages at regular intervals automatically. It makes the communication more efficient when collecting a lot of remote power information. The polling mode offers the precise information of every step required by the monitors. In addition, the PM-213x-CAN also owns the arbitration mechanism which can avoid data collision and error detection.
      CAN Power Meter

  • Utility:
    • Operation mode configuration
    • IP 、 Gateway 、 Mask configuration
    • CAN bus Baud rate configuration
    • CAN BTR0 and BTR1 configuration
    • CAN acceptance filter configuration
    • CAN 2.0A or 2.0B specific selection
    • Error code Responded selection
    • Easy test to transmit/receive CAN messages
    • Easy test to Modbus TCP/Modbus RTU command

Specifications

CAN Interface
Controller
NXP SJA1000T with 16 MHz clock
Transceiver
NXP 82C250
Channel number
1
Connector
2-pin screwed terminal block (CAN_L, CAN_H)
Baud Rate (bps)
10 k, 20 k, 50 k, 125 k, 250 k, 500 k, 800 k, 1 M (allow user-defined baud rate)
Isolation
1000 VDC for DC-to-DC, 2500 Vrms for photocoupler
Terminator Resistor
Jumper for 120 Ω terminator resistor
Specification
ISO-11898-2, CAN 2.0A and CAN 2.0B
UART Interface
COM 1
RS-232
COM 1 Connector
5-pin screwed terminal block (TxD, RxD, RTS, CTS, GND )
COM 2
RS-485 (Self-turner inside)
COM 2 Connector
2-pin screwed terminal block (DATA+, DATA-)
Baud Rate (bps)
110, 150, 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
Data bit
7, 8
Stop bit
1
Parity
None, Even, Odd
Ethernet Interface
Controller
10/100Base-TX Ethernet Controller (Auto-negotiating, Auto_MDIX)
Connector
RJ-45 with LED indicator
Power
Power supply
Unregulated +10 ~ +30 VDC
Protection
Power reverse polarity protection, Over-voltage brown-out protection
Power Consumption
2.5 W
Mechanism
Installation
DIN-Rail
Dimensions
72mm x 122mm x 33mm (W x L x H)
Environment
Operating Temp.
-25 ~ 75 °C
Storage Temp.
-30 ~ 80 °C
Humidity
10 ~ 90% RH, non-condensing

Related Products