WISE-7519ZM/S
10-channels universal AI, 3-channels DO and 2-port Ethernet Switch with DB-1820
Features
Web-programmable controller, 32-bit CPU, 512 KB SRAM, 512 KB Flash, 10 channels of analog input / 3 digital output channels, 2 Ethernet ports, PoE, Modbus TCP, MQTT, with DB-1820 terminal board
- Runs on browsers, no extra software tool is required.
- No more programming, Web pages provided for control logic editing.
- IF-THEN-ELSE logic rules execution ability.
- Built-in I/O (AI: 10 Channels; DO: 3 Channels)
- Support I/O Moniitoring/Control, Counter, Timer, Schedule, Email sending and CGI Command sending operations.
- Modbus TCP Protocol for SCADA System Integration.
- IEEE 802.3af-compliant Power over Ethernet (PoE).
- 2-port Ethernet Switch for Daisy-Chain Topology.
- MQTT Protocol for IT & IoT (Internet of Things) System Integration.
Applications
Building Automation, Factory Automation, Machine Automation, Remote Maintenance, Remote diagnosis and Testing Equipment, etc.
Specifications
Hardware Specifications
Thermocouple Input
Channels
10 (Differential)
Input Type
±15 mV, ±50 mV, ±100 mV, ±150 mV, ±500 mV, ±1 V, ±2.5 V, ±5 V, ±10 V
±20 mA, 0 to 20 mA, 4 to 20 mA (Jumper Selectable)
Thermocouple (J, K, T, E, R, S, B, N, C, L, M, and LDIN43710)
Resolution
16-bit
Sampling Rate
10 Samples/Second (Total)
Accuracy
±0.1% of FSR or better
Zero Drift
±0.5 μV/°C
Span Drift
±25 ppm/°C
Over Voltage Protection
240 Vrms
Input Impedance
>300 kΩ
Common Mode Rejection
86 dB Min
Normal Mode Rejection
100 dB
Temperature Output Consistency
Yes
Stable Temperature Output in the Field
Yes
Open Wire Detection
Yes
Virtual Channel to Channel Isolation
±400 VDC
Digital Output
Channels
3
Type
Isolated Open Collector
Sink/Source (NPN/PNP)
Sink
Max. Load Current
650 mA/Channel
Load Voltage
5 VDC to 50 VDC
Overvoltage Protection
60 VDC
Overload Protection
1.4 A
Short-circuit Protection
Yes
Communication
Ethernet Port
2 x RJ-45, 10/100 Base-TX, Swtich Ports
PoE
Yes
Protocol
Modbus TCP, MQTT
LED Indicators
for System Running
Yes
for Ethernet Link/Act
Yes
for I/O Channel Status
Yes
for PoE Power
Yes
2-Way Isolation
I/O
2500 VDC
EMS Protection
ESD (IEC 61000-4-2
±4 kV Contact for Each Terminal and
±8 kV Air for Random Point
EFT (IEC 61000-4-4)
±2 kV for Power Line
Surge (IEC 61000-4-5)
±2 kV for Power Line
Power
Reverse Polarity Protection
Yes
Powered from Terminal Block
12 to 48 VDC
Powered from PoE
Yes, IEEE 802.3af, Class1
Consumption
3.6 W (Max.)
Mechanical
Dimensions (L x W x H)
114mm x 97mm x 38mm
Installation
Wall mounting
Environment
Operating Temperature
-25 °C to +75 °C
Storage Temperature
-30 °C to +80 °C
Humidity
10 to 90% RH, non-condensing
Software Specifications
Functions
Rule Configuration Website
Access Web server on WISE controllers to edit and upload logic rules through web browser.
72 IF-THEN-ELSE Logic Rules
3 IF conditions with AND or OR operators
3 THEN actions and 3 ELSE actions
48 Internal Registers
Hold temporary variables and read/write data
24 Timers
Delay / Timing functions.
24 Schedules
Setup prescheduled routine tasks.
24 Emails
Send Email messages to pre-set Email receivers.
24 CGI Commands
Send pre-set CGI commands.
24 Recipes
Set up THEN/ELSE action groups.
8 P2P remote modules
Set up the connection information for the remote WISE modules.
Modbus TCP Protocol
Real time control and monitoring I/O channels and system status of controllers via SCADA software.
MQTT Protocol
Real time message publish/subscribe mechanism for I/O channels and system status via IT/IoT software.
IF Conditions
DI Channel
ON, OFF, ON to OFF, OFF to ON, Change
Internal Register
=, >, <, >=, <= (value)
DI Counter
DO Counter
=, >, <, >=, <= (value), Change
Timer
Timeout, Not Timeout
Schedule
In Range, Out of Range
P2P
DI, AI, DI counter, DO counter, IR
Rule Status
Enable, Disable
THEN / ELSE Actions
DO Channel
ON, OFF, Pulse Output
Internal Register
Change the value
DI Counter
DO Counter
Reset
Timer
Start, Reset
Schedule
Enable, Disable
Email
MQTT message
CGI Commands
Send
Recipe
Execute
P2P
DO(On/Off), AO, IR
Rule Status
Enable, Disable