Data acquisition controller with 8-channel Isolated Sink Type Open Collector Digital Output and 8-channel Isolated Digital Input (32-bit Counter), Power-over-Ethernet (PoE) function and easy web configuration, can send Email alarms based on configurable conditions and allow users to implement IF-Then-Else type control logic. Communicable over Modbus TCP. Mini OS7 Operating System. Supports operating temperatures of -25 °C ~ +75 °C (-13F ~ 167F).
WISE (Web Inside, Smart Engine) is a product series developed by ICP DAS that functions as control units for use in remote logic control and monitoring in various industrial applications. WISE offers a user-friendly and intuitive web site interface that allows users to implement IF-THEN-ELSE control logic on controllers just a few clicks away; no programming is required. With its powerful and easy-to-use features, it will minimize the learning curve, shorten time to market and dramatically reduce the effort and cost spent on system development.
WISE-7144 follows IEEE 802.3af-compliant (classification, Class 1) Power over Ethernet (PoE) specification. It allows receiving power from PoE enabled network by Ethernet pairs (Category 5 Ethernet cable). This feature provides greater flexibility and higher efficiency therefore simplifying systems design, saving space, reducing cables and eliminating the requirement for dedicated electrical outlets. Meanwhile, in case under a non-PoE environment, WISE-7144 will still be able to receive power from auxiliary power sources like AC adapters or battery, etc.
This module WISE-7144 supports Modbus/TCP protocol to make seamless integration with SCADA software available. It features 8-channel isolated open collector outputs and 8-channel isolated wet contact digital inputs. Each output channel supports 300mA current driving +10 ~ 40 VDC and each digital input channel supports counter input.
- Built-in Web Server for IF-THEN-ELSE rule setting
- Built-in IF-THEN-ELSE rule engine for logic operation
- No more programming. Just click and get done!
- Support IO, Counter, Timer, Email operations
- Modbus/TCP Protocol for SCADA Software Seamless Integration
- IEEE 802.3af-compliant Power over Ethernet (PoE)
- 10/100 Base-TX Ethernet
- 2-way Isolation/ESD Protection
- DO Type: 8 Isolation Open Collector (Sink Type)
- DI Type: 8 Isolation Wet Contact (Sink/Source)
Building Automation, Factory Automation, Machine Automation, Remote Maintenance, Remote diagnosis and Testing Equipment, etc.
Reference & Support
|Input Type||Wet Contact (Sink, Source)|
|On Voltage Level||+10 VDC ~ +50 VDC|
|Off Voltage Level||+4 VDC Max|
|Input Impedance||10 kΩ|
|Counters||Max. Count||65535 (16 bits)|
|Max. Input Frequency||50 Hz|
|Min. Pulse Width||10 ms|
|Overvoltage Protection||+70 VDC|
|Output Type||Isolated Open Collector (Sink)|
|Max Load Current||300 mA/channel at 25 °C
Direct drive power relay module
|Output Voltage||+10 VDC ~ +40 VDC|
|Overvoltage Protection||60 VDC|
|Overload Protection||1.1 A|
|Short Circuit Protection||Yes|
|Flash Memory||512 KB|
|PoE Ethernet Port||10 / 100 Base-TX and Automatic MDI/MDI-X|
|2 Way Isolation|
|ESD (IEC 61000-4-2)||4 kV Contact for each terminal|
|EFT (IEC 61000-4-4)||+/-2 kV for Power|
|L3||Ethernet 10/100M Speed|
|Reserve Polarity Protection||Yes|
|Powered from terminal block||Yes, 12 ~ 48 VDC|
|Powered from PoE||Yes, IEEE 802.3af, Class1|
|Dimensions (W x H x D)||72 mm x 123 mm x 35 mm|
|Installation||DIN-Rail or Wall mounting|
|Operating Temperature||-25 ~ +75 °C|
|Storage Temperature||-30 ~ +80 °C|
|Humidity||10 ~ 90% RH, non-condensing|
|Rule Configuration Website||Access Web server on WISE controllers to edit and upload logic rules through web browser.
|36 IF-THEN-ELSE Logic Rules||3 IF conditions with AND or OR operators
3 THEN actions and 3 ELSE actions
|48 Internal Registers||Hold temporary variables and read/write data via Modbus/TCP address.
|12 Timers||Delay / Timing functions.
|12 Emails||Send Email messages to pre-set Email receivers.
|12 CGI Commands||Send pre-set CGI commands.
|12 Recipes||Set up THEN/ELSE action groups.
|8 P2P remote modules||Set up the connection information for the remote WISE modules.
|Modbus/TCP Protocol||Real time control and monitoring I/O channels and system status of controllers via SCADA software.
|DI Channel||ON, OFF, ON to OFF, OFF to ON, Change|
|Internal Register||=, >, <, >=, <=(value)|
|DI Counter||=, >, <, >=, <=(value), Change|
|Timer||Timeout, Not Timeout|
|P2P||DI, AI, DI counter, DO counter, IR|
|Rule Status||Enable, Disable|
|THEN / ELSE Actions|
|DO Channel||ON, OFF, Pulse Output|
|Internal Register||Change the value|
|P2P||DO(On/Off), AO, IR|
|Rule Status||Enable, Disable|