4 Port Isolated Protection CAN Communication Board with 9-Pin D-Sub Connector

PISO-CAN-400D

4 Port Isolated Protection CAN Communication Board with 9-Pin D-Sub Connector

Features

*** This product has been phased out and replaced with PISO-CAN400U-D ***

The CAN (Controller Area Network) is a serial communication protocol, and efficiently supports distributed real-time control with a very high level of security. It is suitable for networking "intelligent" devices as well as sensors and actuators within a system or sub-system. In CAN networks, there is no addressing of subscribers or stations in the conventional sense, but instead prioritized messages are transmitted. As a standalone CAN controller, PISO-CAN400/CAN200 can represent an economic solution of an active CAN board. It has two or four independent CAN bus communication ports with 5-pin screw terminal connector or 9-pin D-sub connector, and has the ability to cover a wide range of CAN applications. Besides, PISO-CAN400/CAN200 uses the new CAN controller Phillips SJA1000T and transceiver 82C250/251, which provide bus arbitration, error detection with auto correction and re-transmission function. It can be installed in a 5V PCI slot and supported truly “Plug & play”.

Applications

  • DeviceNetCANopen
  • CAN J1939
  • SDS(System Wide Network) protocol application.
  • CAN bus communication application
  • Industry Automation

Industry

  • Four independent CAN bus 2.0A/2.0B communication ports.
  • Compatible with CAN specification 2.0 parts A and B.
  • On-board optical isolation protection.
  • Programmable transfer rate up to 1 Mbps.
  • Jumper select 120Ω terminator resistor for each port.
  • Direct memory mapping to the CAN controllers.
  • 33MHz 32bit 5V PCI bus (V2.1) plug and play.

In order to apply the PISO-CAN200/400 to CAN network with NI LabVIEW, we provides a LabVIEW toolkit for the purpose. It is a useful tool to develop the CAN-relative application in NI LabVIEW environment by using PISO-CAN200/400. It is easy to use and can help user to rapidly reduce their program development cycle. If users want to develop a LabVIEW industrial application with CAN network, the LabVIEW CAN driver is very helpful.

CAN LabVIEW Tool Features:

  • Supports extension arbitration id
  • Supports debug receive mode
  • Start byte of output
  • Scaling range to select
  • Two languages: German and English
  • Selectable data rates (baud):
    • 10K, 20K, 50K, 125K, 250K, 500K, 800K, 1M
    • and user defined.


In order to easy to use the PISO-CAN200/400 to CAN network for user. We provides a DASYLab version 8.0 toolkit for the purpose. It is a useful tool to develop the CAN-relative application in DASYLab environment by using PISO-CAN200/400. It can help user to rapidly reduce their program development cycle. If users want to develop a DASYLab industrial application with CAN network, the DASYLab CAN driver is very helpful.

CAN DASYLab Tool Features:

  • Support extension arbitration id
  • Support maximum 64 CAN ports
  • Start byte of output
  • Scaling range to select
  • Sample rate from 50 ~ 5000 Hz
  • Two languages, German and English
  • Selectable data rates (baud):
    • 10K, 20K, 50K, 125K, 250K, 500K, 800K, 1M
    • and user defined.


In order to apply the CANopen protocol on the PISO-CAN/200/400 easily, we provides two CANopen application Tools, which are CANopen library and CANopen diagnosis application tool. If users want to develop an industrial application with CANopen protocol, the CANopen library is very helpful to be applied with the PISO-CAN200/400 as the CANopen devices with the features of CANopen protocol. Besides, if the monitor and diagnosis of CANopen message on the CAN network is considered, the CANopen diagnostic application tool can be used to achieve this purpose.

CANopen Application Tool Features:
  • Follow DS301 version 4.02
  • Auto defecting CANopen slave devices
  • IO monitor
  • Dynamic PDO
  • NMT master
  • Support the Guarding and Heart beat protocol and SYNC message.
  • Selectable data rates (baud):
    • 10K, 20K, 50K, 125K, 250K, 500K, 800K, 1M


DeviceNet is a low level network that provides connections between simple industrial devices (sensors, actuators) and higher level devices (controllers). It allows direct peer to peer data exchange between nodes in an organized and, if necessary, deterministic manner. We provides DeviceNet library for users to develop the specific DeviceNet application by PISO-CAN200/400. In addition, we also provide the DeviceNet diagnosis application tool to monitor and diagnose the DeviceNet message through CAN network. It provides the DeviceNet communication protocol interface to control and analysis the DeviceNet slaves.

DevcieNet Application Tool Features
  • Auto defecting DeviceNet slave devices
  • IO monitor
  • Message monitor & diagnosis
  • Support UCMM capable devices
  • Support the Predefined Master/Slave connection set
  • Selectable data rates (baud):
    • 125K, 250K, 500

 

Specifications

  • CAN controller: Phillip SJA1000T
  • CAN transceiver: Phillip 82C250/251
  • Signal support: CAN_H, CAN_L
  • 16 MHz CAN controller frequency
  • Connector:
    • 5-pin screw terminal connector
    • 9-pin D-sub connector
  • Isolation voltage: 2500Vrms
  • Environment:
    • Operating temperature: 0°C ~ 60°C
    • Storage temperature: -20°C ~ 80°C
    • Humidity: 0 ~ 90% non-condensing
    • Dimensions: 130mm X 110mm
ICP DAS USA,Inc.